Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON DT RV300RKC2 106 NT - PA612-GF30 - RadiciGroup High Performance Polymers

Check here, which other Radilon D datasheets, application examples or technical articles are available in Material Data Center

Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Diagrama

Any use of this information falls under the rules of our disclaimer.

Informação do produto

PA612, 30% glass fibre reinforced injection moulding grade. Heat stabilized. Natural colour.

Suitable for parts requiring high stiffness and good mechanical resistance in direct contact with drinking water and food. Exhibits good dimensional stability, improved hydrolytic stability and very good chemical resistance to disinfectants.
Product developed for applications in civil and industrial water management as well as appliances.

Características de processamento/físicas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Contração após a moldagem, paralelo	0.3 / *	%	ISO 294-4, 2577
Contração após a moldagem, perpendicular	0.7 / *	%	ISO 294-4, 2577

Propriedades mecânicas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Módulo de tração	8800 / 7900	MPa	ISO 527
Tensão na ruptura	165 / 130	MPa	ISO 527
Deformação na ruptura	3.4 / 4.1	%	ISO 527
Resistência ao impacto Charpy , +23°C	70 / 80	kJ/m²	ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C	13 / 15	kJ/m²	ISO 179/1eA

Propriedades térmicas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Temperatura de fusão, 10°C/min	210 / *	°C	ISO 11357-1/-3
Coef. de expansão térmica linear, paralelo	20 / *	E-6/K	ISO 11359-1/-2
Coef. de expansão térmica linear, perpend.	120 / *	E-6/K	ISO 11359-1/-2
Flamabilidade a 1.5mm esp. nom.	HB / *	class	IEC 60695-11-10
Espessuras do tubo de teste	0.8 / *	mm	-
Cartão Amarelo (yellow card) disponível	sim / *	-	-

Propriedades elétricas	Seco / Cond	Unidade	Método de ensaio
ISO Dados
Resistividade volumétrica específica	1E13 / 1E11	Ohm*m	IEC 62631-3-1
Resistividade superficial específica	* / 1E10	Ohm	IEC 62631-3-2

Outras propriedades	Seco / Cond	Unidade	Método de ensaio
Absorção de água	1.9 / *	%	Sim. to ISO 62
Absorção de umidade	0.7 / *	%	Sim. to ISO 62
Densidade	1290 / -	kg/m³	ISO 1183

Diagrama

Características

Processamento

Moldagem por injeção

Forma de entrega

Granulado, Cor natural

Aditivos

Desmoldante

Características especiais

Estável contra o calor

Resistência Química

Estabilidade hidrolítica

Certifications

Contacto com alimentos, Contato com água potável

Disponibilidade regional

América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África

Outras informações

Moldagem por injeção

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.10%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
260 - 290°C	80 - 90°C	medium

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.